Now that Leica has released a pure black and white camera, the Leica M-Monochrome, I started to think about the advantages a pure black and white camera has compared to a colour camera.

I guess you could remove the Bayer filter, but would this give you higher resolution, better contrast?

I assume there is advantages with a pure black and white camera, since Leica has made one, but what are they?


3 Answers 3


The biggest advantage is that you get 3X more light sensitivity.

With a bayer filter, every photosite gets 1/3 of the light that falls on it because the filter blocks 2/3 of incoming light to filter for one primary color. So the sensor becomes more sensitive to light. That means that less amplification of the read-out signal to get the same ISO as with a conventional sensor. The end-result is that you get lower noise at each ISO sensitivity.

There is no need for an Anti-Aliasing filter, so you get better sharpness and micro-contrast. As Nikon proved it though, this is not necessary for Bayer-based cameras but is usually the case. When a camera uses an AA filter, it blurs the light before it reaches the sensor to avoid the occurrence of an artifact called moire. Any time you blur something, you reduce contrast because you spread light over multiple pixels. Without an AA filter, the blurring does not happen and you get better contrast.

B&W sensors also obviously do not need Bayer-interpolation. This means that the readout is the image data and there is no question of softness introduced by interpolation (or the AA filter that is not there) and no need to sharpen at the capture level, although you may sharpen when processing for your output medium (print, screen or other).

  • 1
    \$\begingroup\$ It might be asking too much, but could you try to elaborate on this? I do now why you get higher sensitivity, but not sure it's clear to everyone. The same goes for the contrast. \$\endgroup\$ May 12, 2012 at 15:28
  • \$\begingroup\$ @HåkonK.Olafsen - Done :) \$\endgroup\$
    – Itai
    May 12, 2012 at 19:39
  • \$\begingroup\$ Are you sure its a full 3x? \$\endgroup\$ May 14, 2012 at 4:33
  • \$\begingroup\$ Yes. It's pretty simple. Each pixel gets only 1/3 of the light because the filter removes 2/3 to be left with only one primary color. \$\endgroup\$
    – Itai
    May 14, 2012 at 12:16
  • \$\begingroup\$ That assumes perfect filters that let in all of the selected primary, and nothing else. They could vary from perfect and either allow some other color leakage, or reduce the intensity of that color. While 3x makes sense, it could vary up or down depending on the filter characteristics of the compared color sensor. \$\endgroup\$
    – Skaperen
    May 15, 2012 at 5:27

In addition to Itai's excelent points, it is also worth mentioning that processing the RAW image becomes significantly easier.

With a normal bayer pattern, each pixel on the sensor records only one color (red, green, or blue). The RAW converter has to process this information into an image where each pixel contains full color information. So each pixel in the final image has to be based on at least three pixels from the RAW data. But in reality it is more (the simplest raw converter uses 4 pixels from the RAW data for each pixel in the final image, and this is too simple to produce excellent results). So This conversion inevitable leads to loss of sharpness.

A monochrome sensor shouldn't have this limitation.


I'd like to note that with a B&W sensor, you only capture luminance, so, if you need to apply colour filters you must do so physically with actual optical filters at capture time.

But you can do this in post when you convert an RGB image to B&W, for example by mixing channels or adjusting individual channel properties before converting.

I'm not stating any of these approaches is negative or positive, but they have intrinsic considerations that can impact on budget, technique, workflow and time to final output.

Personally I think a B&W brings back some of the film era experience, so I hope I can fit this camera in my budget some day, but in the meanwhile, I'll take advantage of the post flexibility of channel mixing and individual adjustment.

  • \$\begingroup\$ Applying filters at capture time: just like with film! \$\endgroup\$ Jun 16, 2022 at 12:24

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.