7
\$\begingroup\$

As you can see, the reflections impair the visibility of the objects behind the glass quite a lot. This image is fairly old (2009), so that I can't revisit the site for a better shot.

enter image description here

Software: darktable + Gimp 2.8.

Improve this question
\$\endgroup\$
0

2 Answers 2

Reset to default
9
\$\begingroup\$

Although I am not a Gimp User, but the process I use in Photoshop will most likely be very similar and it should not take more than 5 minutes to reach a satisfactory result.

enter image description here

I will start with the Clock first

  1. COPY VIA NEW LAYER, the bottom half of the clock
  2. FLIP IT HORIZONTAL to cover the top part of the clock
  3. SKEW, DISTORT and WARP this Layer until it matches the top part of the clock
  4. CREATE a LAYER MASK on this New Layer and INVERT so it shows Black
  5. Select White as the top colour on your Colour Palette
  6. Use the BRUSH TOOL to paint over and reveal the new adjustment.
  7. CLONE TOOL to tidy up and to bring back the Red Second Hand needle

Now for the Platform Indicator

  1. Create a Curve Adjustment Layer, but DON'T do anything just yet.

  2. Then from the COLOUR SELECT, use the dropper tool to Select the areas you want reduced (The Reflections area)

  3. This will now allow the Curves Adjustment to only effect this.

  4. Pull down the curve adjustment until it matches. ( you may have to do several separate passes to achieve this.

  5. Unfortunately, this will effect some of the writing too ( Wilhemshagen) and for this, you need to either.....

  6. ...... Clone in the letters from other more readable areas

  7. ...... Or, create COPY VIA LAYER for each letter required and bring them down to create Wilhelmshagen.

  8. With the “W”, you will need to draw that in as there isn’t one to copy from

  9. Finally, just clone and tidy up

Improve this answer
\$\endgroup\$
3
  • 1
    \$\begingroup\$ This is an excellent result. The process is similar to what I thought of doing it in Photoshop. Unfortunately, I couldn't find a "select by brightness" or similar in Gimp \$\endgroup\$
    – jng224
    Commented Dec 14, 2020 at 16:33
  • 3
    \$\begingroup\$ thanks for the comment. Just had a look at the Gimp Docs and it says that colour select is located in - Tools > Selection Tools > By Color Select or by SHIFT+O. I have only ever used GIMP very briefly, but considering changing as not happy with the Adobe CC Subscription any more.. \$\endgroup\$
    – Abdul N Quraishi
    Commented Dec 14, 2020 at 18:36
  • \$\begingroup\$ The clock turned out to be the easiset problem to solve. I had to copy many letters (or parts of them — the S, for instance) to get rid of the reflections. Sometimes I had to fiddle around with the curves and then soft-focus the whole lot as it turned out quite noisy. But nevertheless: Many thanks for your tips! :) \$\endgroup\$
    – Neppomuk
    Commented Dec 27, 2020 at 18:34
6
\$\begingroup\$

I could come up with the following using Gimp:

enter image description here

As you can see, I only removed the reflection at the word "Erkner". You would probably get better results using a RAW version of the photo and by spending some more time.

Here is what I did:

  • Open the photo in Gimp and create a duplicate
  • Create a layer mask on the duplicate layer. Fill this layer mask to cover all the reflections (or one specific reflection). The more precise you are here, the better your result will be
  • Add adjustments to the duplicate: This depends on your photo. In this case, it was a combination of lowering the brightness, slightly increasing the contrast, some hue shift and lowering the saturation. The best practice is to look at what is different to the non-reflected areas and change your settings to match them as close as possible
  • Then, I finally did some clean-up with the healing brush tool and brush. This included painting over some weird-looking areas and refining my edge (I wasn't very precise with my mask)

Credits should go to this video (he uses Photoshop, but the process is the samein Gimp).

Improve this answer
\$\endgroup\$

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.