5

Using the Godox TT350N as a means to control your other Godox speedlight is a perfectly viable option. If you later decide to buy a dedicated trigger, you can control both of them. The only drawback is that the controls on the flashes themselves are not as straight forward as they are on the Godox X2 or Xpro. Plus you will probably never use the speedlight ...


4

I have currently a Nikon D850 along with a SB-700 flash, whose main purpose is to shoot cosplays in events. I'm happy that using it on the hotshoe would get better photos than without it, but still I'm not satisfied. So I'd like to experiment to having it off-camera. Now, I've read [various] ways to trigger the flash off-camera, and I still am ...


3

I wanted to know if I can use Godox AD 200 without the transmitter such as X1 T or Pro? Yes, there are several methods one may use to trigger a Godox AD200 without using a Godox 2.4Ghz transmitter. You could use a wired connection between your camera's PC terminal (or an adapter mounted on the hot shoe if your camera does not have a PC terminal) and the ...


2

why doesn't it come with the flashlight itself? This is in general for flash heads, not only the Godox brand. Imagine this scenario. You want a 3 light setup for a portrait... You would end with two triggers on the shelf and one in your camera. If you need to illuminate a big building... You got the idea. The remote trigger is not a required device. It is ...


2

...since the YN 560 IV can control other wireless flashes can it also control and group the [Neewer] TT560 flash since it's connected to a wireless receiver now? No. It cannot; all you can do is fire the flash in sync. The RF-603 II C, when used as a receiver cannot do power or group control, so there's no way to communicate that to the flash. An RF-605 ...


2

It's a perfectly viable plan to use a TT350-N (or li-on V350-N) as your iTTL transmitter, but it's not just smaller and less powerful than a V860II-N, it also lacks CLS/AWL capability, it only swivels 270º not 360º, it has no sync port, no external battery port, no recycle beep, and it is not designed to do cross-brand TTL as a radio slave like the full-...


1

The Nikon D5100 doesn't have high-speed sync (HSS) capability (apparently Nikon is known to reserve this feature to higher end cameras, as opposed to other manufacturers), so this option is useless in the X2T when used with this camera. Concerning the X2T delay option, as mentioned in the manual this setting [sets] the firing delay in high-speed sync ...


1

I just did the same, using my SB700 (and D850)with the Godox X pro N and the X 1 receivers. It worked great practicing in the house, either on Manual or TTL (on the flashes), but when I tried to set up a quick shot today, the flashes won't flash when on remote mode. I did not remember changing anything after intially finding that the set up was very simple ...


1

At a bare minimum, you need to make sure that: Your transmitter matches your camera. If you have a Canon camera, you need the Canon version of the X2T (the X2T-C). The Nikon (X2T-N) or Sony (X2T-S) version will not work on a Canon camera, and vice versa. The 'Channel' selected on the transmitter and the channel selected on the flash's radio receiver are the ...


1

If you have changed the AF mode from 'One Shot AF' to 'AI Servo AF', the assist beam will not operate with any flashes or triggers that have assiste beams, including Canon external flashes and even the popup flashes on Canon cameras that have them. In order to use an AF assist light, the AF mode must be operating in 'One Shot AF' mode. If you are using 'AI ...


1

While the D3200 and your Neewer-branded* Voking VK750 II can both communicate iTTL signals, the Neewer-branded Godox FC16 Rx/Tx triggers cannot. If you look at the pin on the foot of the transmitter, and the hotshoe on top of the receiver, you'll notice there's only a single pin/contact. This is the way the sync (fire) signal is communicated. All the ...


1

If you already have a regular flash for your Sony a7R III, you can use that to trigger the AD200 using it’s built in S1/S2 optical slave mode. Another basic method is using a Sync Cord with a 3.5mm plug. The older FT-16 transmitter/receiver system is also compatible with the AD200.


1

I figured out the problem. The hotshoe on the Canon 6D was loose. It was causing the contacts on the yn622c-tx to not touch. Those contacts are a hair shorter than the Canon speedlite's contacts, which is why the 6D + speedlite was working fine. I found a video on how to fix a loose hot shoe. https://www.youtube.com/watch?v=s_neI06o3c0 After tighten the 4 ...


Only top voted, non community-wiki answers of a minimum length are eligible