1

This question already has an answer here:

I have a Canon Rebel T5, and a 75-300mm lens. I shoot and I get a lot of blurry unfocused shots. What can I do to improve this?

marked as duplicate by scottbb, Olivier, Philip Kendall, MikeW Mar 26 '17 at 20:34

This question has been asked before and already has an answer. If those answers do not fully address your question, please ask a new question.

  • 2
    The same way you get in-focus, not-blurry shots with a high quality telephoto zoom: good technique. – Michael C Mar 17 '17 at 2:58
4

Basic telephoto lens technique is different from shooting with a kit lens. There are additional factors you have to consider.

Lens weaknesses

First off, the Canon 75-300 lenses are very old in design and they are consumer-grade, which is why they're so inexpensive. It's a relatively limited lens, and you have to know what its weaknesses are and shoot away from them.

Stabilizing the camera

Longer focal lengths make camera shake blur easier to capture, both by magnifying the shake, and also by being longer and therefore less stable to handhold. If you are shooting something that isn't moving, then you need to look at how stable your camera is. Consider using a tripod or monopod. Consider how you hold your camera. If your model of the 75-300 (there were dozens between the Mark I, II, III, USM, and IS variants) has image stabilization, turn it on. And watch your shutter speed.

Shutter speed

There's a rule of thumb that to mitigate blur from camera shake, you must shoot with a shutter speed at or faster than 1/focal_length. With crop factors and higher-resolution sensors, many folks will throw in the crop factor or double that number. So, with a 300mm lens, on a T5, you probably need a shutter speed of at least 1/500s or 1/600s or faster. And this assumes you have good handholding technique. This is not a hard-and-fast number that will always work, just a guesstimate and a guideline. Some folks may be able to use a slower shutter speed. Some folks will require a faster.

If your subject is moving, then the shutter speed you'll need to "freeze" the action depends on how fast your subject is moving. It may be much higher than 1/focal_length.

Mastering autofocus

If your copy of the 75-300 lacks USM, then AF speed can be tough. Be sure you know how to select an AF point or use the AF point array in your camera, and what the different modes are. Know how to aim for an area of high contrast (where a white edge meets a black one). Know how to half-press and/or how to use back-button autofocus. And you will need plenty of light. Consider a flash.

Aperture and focal length settings

In addition, the 75-300 tends to be softest when wide open and at the extremes of the zoom range. Backing off from 300mm a little, and stopping down into the f/8-f/16 range will all help get sharper results.

However. Shooting, say, at f/11 and 1/500s, even on a sunny day, probably requires you to shoot at at least iso 400, if not up to iso 1600, depending on how much sunshine you get. Don't be afraid to crank up the ISO--it's why you got a larger-sensored camera, after all.

You'll routinely see the 75-300 III trash-talked on messageboards and people telling you to just give up and go get a big white L lens. That's fine for them to say, since it's not their $1000+ you'll be spending to get one. :) But you can take decent images with a 75-300 if you know what conditions it does well in, and avoid trying to shoot in situations where it's not an appropriate choice.

This picture was taken by me with an old Canon XT (350D) and the non-USM/non-IS version of the EF 75-300 III. The EXIF on it shows 300mm, iso 1600, f/11, 1/1000s. It was taken handheld, and this is a straight-from-the-camera JPEG file.

image taken with 75-300 III

See also: Why are my photos not crisp?

Not the answer you're looking for? Browse other questions tagged or ask your own question.