My Canon EOS 500D camera shows white photos after capturing photos. I'm not referring to the balance of the photos. The photos that I try to capture comes out white. What is the cause?

  • 4
    \$\begingroup\$ What settings are you using? Maybe you are just overexposing the photos? \$\endgroup\$
    – osullic
    Apr 20, 2022 at 18:34
  • 1
    \$\begingroup\$ In addition to settings, what environment are you shooting in? What is the light source? Is this a new problem? If not, is it associated with gear change, like use of flash or different lenses? \$\endgroup\$
    – xiota
    Apr 20, 2022 at 20:29
  • 1
    \$\begingroup\$ Does this answer your question? Why is my long exposure shot all white? \$\endgroup\$
    – Michael C
    Apr 21, 2022 at 8:34

2 Answers 2


Sounds like you are overexposing. Try setting the mode dial to P or Auto. These modes automatically dials in a correct exposure, at least as correct as the built in light meter can determine it. If this solves your white images, notice the settings the camera chose; ISO, shutter speed and aperture.

Then go back to the mode you were originally on, and dial in the same settings. You should now have a more or less correct exposure.

Also notice that there is an exposure “needle” in the bottom of the viewfinder. This should be placed in the middle to achieve correct exposure (again, according to the built in meter)

To understand how to dial in correct settings, have a look at What is the "exposure triangle"?


When an image is all white it means the entire scene is overexposed to the point all three color channels are fully saturated.

Think of it this way: If a scene has twice as much blue as red and green when properly exposed the amount of blue recorded will be twice the amount of red and green recorded. It also means it is possible to fully saturate the blue without saturating the red and green. But if the red and green are fully saturated then the blue will also be fully saturated because that would mean the blue was exposed twice as bright as what was needed to max out the blue channel.

With a digital sensor (or even with film) it is not possible to increase the level of a color past full saturation - that is the highest value for that color recordable by the sensor or film. If you just expose barely long enough for the entire photo to be pure white (full saturation in all three color channels) or if you expose for ten times that long the photo will be equally white. The one exposed for ten times longer won't be ten times as bright because the shorter exposure also let enough light strike the sensor to fill all the pixel wells until they were full.

It's like a rain bucket. If the rain bucket is only big enough to hold two inches of rain and it rains four inches, the bucket won't be any fuller than when it was overflowing after the first two inches had already filled it up. If a bucket that can only hold 2 inches on one side of the yard got 2 inches and a same size bucket bucket on the other side of the yard had four inches of rain fall on it, they'll both be equally full. We'll have no way of knowing how much more rain might have fallen on either side of the yard.

In order for an image to contain usable information (which is what we would call a properly exposed photo), some of the "buckets" (i.e. pixel wells) have to be fuller than others. If they're all totally full then there is no difference between any part of the image and there is no usable information.

To reduce exposure you have several choices:

  • Reduce the camera's sensitivity by setting it to the lowest ISO setting.
  • Reduce the amount of light entering the camera by using a narrower aperture setting (higher f-number).
  • Reduce the amount of time the light is entering the camera by using a shorter shutter time. Each time you halve the amount of time the shutter is open you halve the amount of light that strikes the sensor. If an image is pure white it usually means you need to halve the shutter time at least three times (i.e. three "stops"). For example, instead of 2 minutes (120 seconds), try 15 seconds. Or instead of 1/30 second try 1/250 second.
  • Reduce the amount of light striking the front of the lens by using a neutral density filter. They are available in various strengths from one stop (half the light) to ten stops (1/1024 the light). Avoid cheap "variable density" filters if possible. They cause a lot of image quality problems and color shifts.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.