3

Hi fellow photographers

I'm a hobby film photographer for a few years now having a basic understanding of photographing, developing and scanning + postprocessing.

In the past months i've shot only few photographs due to some global pandemic. I've developed with Cinestill CS41 for some time now with great results. As the first negatives last year had the desaturated look, i've thought the chemistry soup was overused.

Yesterday i cooked a fresh CS41 Soup and bottled it up. Afterwards i developed a fresh roll i shot last week in the mountains just to find out that the problems persist:

  • very muddy/desaturated look (it was bright daylight and fresh green trees)
  • sprocket light leaks (im not sure what they're caused by)

I've used a Canon AE-1 which light seals have been replaced last year and worked fine since. Maybe i should check them. Portra 400 was in the Camera, set to ISO 200 and i metered for the shadows (even though it looks muddy, i think its obvious i overexposed +1). Developed as always: 3:30 at 49°C Developing and 8:00 at BleachFix. Final rinse with demineralized water + a splash of ipa for better drying. All inside the labbox 2. Scanned as always with the Epson V550 in Vuescan. The Epson has a Anti-Newton-Ring glass inset. Cropped the image, took a bit of the orange as white balance, used negative lab pro, with default presets. Never had this look before with these settings. If i invert the colors myself by using the "RGB Curves Method" i get a huge bluecast which also would normally never happen in this method.

  • What could cause the sprocket light leaks? door seals have been replaced and seems odd they cause these.
  • Why are my negatives so muddy/desaturated?
  • Why am i such a horrible photographer :D

Screenshot of Lightroom with an image of Mountains behind a Lake The negative of the first one Screenshot of Vuescan Image of what it should look like

What it actually looked that day

6

Your "sprocket light leaks" don't cross into the negative rebate, so they're not light leaks.

The marks are blue/cyan on the negative (hence orange in the scan), and darker in the scan than the surrounding image area, suggesting they're due to local underdevelopment. This is what I'd expect from bromide drag, which is caused by insufficient agitation.

Standard C-41 process normally calls for either continuous agitation or five seconds agitation every thirty seconds -- if you're agitating less than this latter you could have problems with bromide drag, even with fresh color developer.

Another potential contributor is overexposure -- the more exposed your film is, the more bromide it releases during development, meaning more exposed film (for instance, film that "saw" the bright sky) is more prone to bromide drag.

Combination here is overexposure and overdevelopment -- you're 10C too high on temperature as well as exposing a stop over (the latter alone usually doesn't cause trouble, though it will produce denser negatives). The muddiness is most likely from your scanning software compensating for this combination.

So, to correct this (aside from observing recommended chemical life in terms of weeks since mixing and rolls processed), be sure to agitate sufficiently, keep your temperature within tolerance (Cs41 wants to start at 102F = 38C, which is calculated to give an average of the C-41 correct 100F after the developer cools during processing), and watch your exposure. Color negative film has a lot of latitude, but this is one of the ways overexposure can have a negative effect.

2
  • you are correct. this might be bromide drag. Maybe not because of agitiation (i constantly agitiate in the labbox, like a waterwheel) .Now that im thinking about, i've completly forgot to presoak my film at all! which is embarrasing to think of. – TheDomis4 Apr 6 at 12:07
  • 1
    Presoaking makes little or no difference -- the only reason I do it is to avoid dyes from the film staining my (replenished) developer stock. The direction of these marks isn't what I'd expect in a LabBox (where the agitation moves solution lengthwise on the film, not crosswise). Might be due to flow when filling the tank, though. – Zeiss Ikon Apr 6 at 13:36

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.