I was surprised to learn that most flashes last only 1/1000s instead of lighting up for the entire exposure time. Why? If the flash were to light up before the shutter opens and turn off after the shutter closes, there would never be flash sync problems.

  • \$\begingroup\$ Maybe a video lamp (light) would do what you want, but obviously you cannot "freeze" movements any more that way. \$\endgroup\$
    – U. Windl
    Nov 12, 2021 at 12:19

6 Answers 6



Fundamentally, it's because of the way flashes work. Flashtubes generate light by discharging a capacitor through a xenon-filled tube. The resulting electric arc produces bright white light. But a continuous electric arc would produce a lot of heat, which would weaken the tube, and it would consume a lot of power, which batteries cannot supply for long.

  • \$\begingroup\$ Comments are not for extended discussion; this conversation has been moved to chat. \$\endgroup\$
    – MikeW
    Jul 17, 2018 at 18:26

That is a true statement, but it misses the big point. (As the shutter would see it), it would simply become continuous light, like any incandescent light bulb (always On for the full shutter duration would be indistinguishable from continuous light). Like continuous light, there would be no motion stopping ability at all.

And even a 500 watt light bulb at 1/200 second shutter is 500 x 1/200 = 2.5 watt seconds of power input, also with very low output efficiency. The regular camera speedlight might be 75 watt seconds, with several times higher output efficiency, and vastly greater light ouput. And is fast, and is vastly more convenient to use than the 500 watt light bulb. Hollywood movies must use continuous lights, but they also have large trucks carrying huge power generators.

But your description is exactly what High-Speed Sync is (HSS), a "flash mode" optionally offered by some cameras and some camera flashes to mimic continuous light (to avoid sync issues). So HSS is a choice if you want to buy it, and want to suffer with its large limitations (of speed and power). But it is merely high speed sync (meaning a fast shutter speed can be used since there is no sync issue), but HSS is the full opposite of high speed flash. No shutter speed can be as fast as a speedlight can be. And continuous light lasting for that longer shutter speed duration would require excessive power (so HSS Mode typically must run at no more than around 20% power level of speedlight mode). Conversely, speedlights simply discharge a large capacitor as a very fast pulse. Which is typically relatively slow at Full power level, but speedlights are called speedlights because they are greatly faster at lower power levels.

The regular normal camera flash mode is called a speedlight (all camera flashes are speedlight type, but only a few studio flashes are) become even much faster at lower power level settings, perhaps 1/30,000 second at maybe 1/64 power. Which is ideal to stop motion like milk drop splashes or hummingbird wings, where the flash can be close to the action. See my site at https://www.scantips.com/speed.html

Flash is often somewhat faster than 1/1000 second, which has great advantage to stop motion, and to offer high peak power for an instant. Photographing the running playing kids when using a speedlight as bounce flash at say 1/2 power will be 1/1000 second duration, and will stop action quite well (even if the default shutter speed is 1/60 second). That assumes indoors, where the ambient continuous light is too weak to show any motion blur.

  • \$\begingroup\$ Why watt-seconds? aren't they just Joules; Watts are J/s so J/s*s is just J! \$\endgroup\$
    – esoterik
    Jul 17, 2018 at 0:20
  • 3
    \$\begingroup\$ Yes, watt seconds are joules. But watt seconds is simply the term commonly used for specs of studio flashes (USA, Europe, Asia, etc.), and watts x seconds is one way input power is computed (but usually WS = 1/2 CV², where C is capacitor size in farads and V is volts). The point I was hoping to make is that flashes (meaning discharge from capacitors) easily have greatly more power than normally feasible for continuous lights. Advantage of flash for photography is power, speed, and lighter/smaller bulk. \$\endgroup\$
    – WayneF
    Jul 17, 2018 at 2:21

Others have addressed the technical side of why strobe flashes are extremely fast.

There are alternative photo lighting technologies which do exactly what you say. This answer addresses the pros and cons of them:

LED-based 'flashes' as seen in phones etc. – these turn on a bright LED for the time it takes to take a photo, then turn it off. They're commonly used in phones because they offer some benefits in phones:

  • The LED can be re-used as a torch

  • An LED driver circuit is considerably simpler than a flash charging and control circuit

  • (not 100% sure how much impact this has, as very occasionally you find a phone with a true flash, but...) Flashes create EM interference, which might impact a phone's functionality, particularly as a phone has multiple antennas in close proximity to where the flash would be; avoiding this simplifies design constraints.

  • The LED and driver circuit is extremely small compared to a flash and charging circuit (which must include a capacitor and inductor).

You'll notice these don't freeze motion, and they aren't as bright as a 'real' flash, despite being illuminated for say 1/50th a second instead of 1/1000th. However, you should consider that they are also massively smaller than a typical flashgun, so the comparison is unfair.

Continuous lighting - commonly seen as studio lights, or video lights.

These are usually LED-based these days, but traditionally would be other (hotter) technologies.

These have pros and cons:


  • You can see the effect of the flash without firing the flash. This was a huge advantage before digital photos, but these days, you can easily take test shots and adjust flashes until you're happy with the result.

  • They provide constant light for video

  • They may be less 'intrusive' or 'disruptive'. This is very subjective. Flashes don't actually hurt or disturb animals (I've done shoots with vets with flash, no issues), and at an event, a single or couple of photographers aren't really disruptive if using flash (humans filter it out), though it can impact video recordings. Some models may find flashes to be an annoyance.

  • Most modern LED continuous lighting is now colour temperature adjustable.

  • They don't freeze motion, which may be a benefit, depending on the shot.


  • For the same brightness, they're larger and much more power hungry than standard flashes. Fine for a studio, but a problem for portable use.

  • They get hot, and make the model hot. Even cool LED lights create much more heat than a strobe, as they're on continuously.

  • There's a limit to the power output of portable continuous lighting, due to power & size constraints.

  • again, they don't freeze motion.


If the flash were to light up before the shutter opens and turn off after the shutter closes, there would never be flash sync problems.

There would also be lower efficiency as some of the light output by the flash that is captured by the lens would not be captured by the camera. It takes about 2-4 milliseconds for a mechanical shutter curtain to transit the sensor of a modern digital camera. So even if the light came on just as the first curtain began to open and went out exactly as the second curtain finished closing, for any shutter time longer than sync speed that's 4-8 milliseconds when some of the light from the flash is hitting part of the front of one of the shutter curtains, rather than the sensor.

Since the output of a speedlight is not constant, it would also mean part of the frame would be lit more brightly than other parts. With a shutter that opens from top to bottom (bottom to top of the inverted image projected by the lens), the bottom of the frame that was lit earlier in the flash's discharge would be brighter than the upper part of the frame that was lit when the energy of the flash was beginning to 'tail'.

enter image description here
Canon 580EX at full power


Started out as a comment to Caleb's nice answer and accidentally turned into answer...

To start a (glowing) discharge high voltage is needed (called breakdown voltage). When the vacuum is broken down the resistance drops almost instantly from near infinity to near zero resulting in insanely high current and low voltage.

Only hard current sources can sustain glowing discharge, which battery/capacitor are not. The flash discharge is therefore a spark discharge rather than glowing discharge.

Another problem would be overexposed scene. Same principle is behind so-called Xenon headlights in cars - their actual name is HID, High Intensity Discharge. The discharge is too bright to be useful for long-lasting illumination.

Plus, the discharge glows not only in visible part of the spectrum, there is a significant radiation in the UV part of the spectrum, another reason not to use it for a long time.

All together:

  • To sustain long-lasting discharge one need hard current source capable of high voltage spikes.
  • The flash unit would be significantly bigger and heavier.
  • The scene will be overexposed,
  • The scene will be lit by intensive UV light.
  • \$\begingroup\$ Great addition! \$\endgroup\$
    – Caleb
    Jul 16, 2018 at 12:48
  • \$\begingroup\$ You're going to have the same amount of UV whether the bulb lights for an instant or for a whole second, for the same total energy output. Fluorescent lights are essentially 'continuous use' flash bulbs, and can be quite suitable for lighting for photographs. \$\endgroup\$ Jul 16, 2018 at 18:26
  • \$\begingroup\$ @whatsisname Only if the shutter time is long enough to allow a complete cycle of the flicker inherent with typical fluorescent bulbs/ballasts. Try shooting at 1/1000, or even 1/250, under fluorescent lights and see how suitable they are. \$\endgroup\$
    – Michael C
    Jul 16, 2018 at 20:34
  • 1
    \$\begingroup\$ @MichaelClark: yes, but that's because of the power grid's design, not specifically due to the bulbs. An electronic controller dealing with this application would easily solve that. \$\endgroup\$ Jul 16, 2018 at 20:48
  • \$\begingroup\$ @whatsisname Yes, but most fluorescent lights under which photographers are often forced to shoot don't have such controllers. \$\endgroup\$
    – Michael C
    Jul 18, 2018 at 1:36

There is a semi-historical reason.

Both pyrotechnical flashbulb and electronic flashes are, by their nature, devices that work on positive-feedback, "escalating" chemical/physical effects (not quite unlike explosions) - the more heat there is, the faster the reaction/discharge - which produces more heat in turn - goes.

Such effects are far harder to control compared to almost literally lighting fuse and getting away (which was what you did with open powder flashes that predated pyrotechnical flashbulbs).

In case of an electronic flash, there is high voltage and current involved. Building a switch for high voltage and current is easy. Building circuitry that can control high voltage and current smoothly is not at all easy (light dimmers, thermostats, induction hobs, power tools sidestep the issue, the method of control used is not smooth at all compared to what you would need for a flash).

Of course, it is technically possible - both FP flash bulbs and slow-sync electronic flashes exist after all - but it is never the cheapest, easiest version.


Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.