2
\$\begingroup\$

I have a D3100, and have a question about back button focusing.

Yesterday I went out with my son to shoot, and I found a lot of my pictures had focus on the wrong part of the image. More than normal. Luckily I took a lot and some were great.

I was using the back button to focus. But as soon as I take a picture the back button stops controlling the focus.

I have to push the shutter half way to 'wake up' the camera, and then the back button focuses again

I made a mistake in that regard by assuming the camera was in focus when hitting the back button did nothing.

Is this expected? Nothing I have read about back button focusing has mentioned this as required.

\$\endgroup\$
2
  • \$\begingroup\$ What focus mode are you using? How are you (or the camera) selecting the AF point(s)? \$\endgroup\$
    – Michael C
    Jul 10, 2017 at 16:03
  • \$\begingroup\$ AF-C focus mode (continuous). Plus single point AF mode. I am moving the focus point myself with the arrows on the back of the camera. \$\endgroup\$
    – peter
    Jul 11, 2017 at 22:25

1 Answer 1

2
\$\begingroup\$

The question has two separate parts: How to get the AE-L/AF-L button to initiate AF and what causes the camera to focus on things that aren't what you want it to focus on. The first is fairly simple. The second could have a book written about it.

If your D3100 is set to AF-ON for the AE-L/AF-L Button Setting under the Buttons setting in the camera's Setup Menu, then the only way to initiate AF is with the AE-L/AF-L button (it's covered on page 146 of the Nikon D3100 Reference Manual). In order for focus to remain active per your selection of AF-C focus mode you'll have to keep the button pressed. If you release the AE-L/AF-L button the focus position of the lens will remain where it was when you released the button. This is helpful if you wish to focus and then recompose without changing the focus mode setting from AF-C to AF-S.

Note that on page 56 of the Nikon D3100 Reference Manual), there's a note that says:

Note from page 56

This implies that AF might not be as accurate in AF-C mode as when in AF-S mode.

The half press of the shutter button may still be required to activate the camera when it is in standby mode, but the half press will not affect AF.

Now on to how to tell your camera where to focus.

The rules that govern how AF systems act aren't always as obvious as we might like. They can't read our mind, or even our eyeballs looking through the viewfinder (unless the camera in question is one of the Canon EOS film cameras from 1995 to 2002 that had Eye-Control Focus).

Different AF systems don't all work the same. To get the most out of them we must learn how each one is designed to work and then practice, Practice, PRACTICE using it until it becomes second nature.

Even an entry level DSLR camera such as your Nikon D3100 has two completely discreet AF systems: The Phase Detection Autofocus (PDAF) system used when you shoot looking through the viewfinder and the Contrast Detection Autofocus (CDAF) system used when you shoot using Live View. Many advanced cameras allow the user to custom configure how quickly and the way in which the AF system responds to certain situations to customize it for a specific shooting environment.

There are some similarities among most PDAF systems, and that seems to be what this question is about. Here are a few things to remember.

  • The PDAF system is still looking for contrast, even though 'contrast' isn't included in the name. The area of highest contrast among all of the active AF points/areas will be what the camera usually attempts to bring into focus. If there is an area of higher contrast right on the edge of an AF point or area's region of sensitivity, that will be what the camera focuses on, not the area of lower contrast that is directly underneath the little square in your viewfinder. There is no "center weighted average" with modern multi-point AF systems.
  • Where you think the focus point is, marked by that little square in the viewfinder, is nowhere near the entire area of sensitivity for each focus point. The camera will focus on the point of highest contrast for any part of the actual coverage area for a given point. If there is an area of higher contrast in the coverage are beyond the actual square in the viewfinder, the camera will focus on the higher contrast area for the full coverage area of the focus point(s) you have selected.
  • Some "points" can overlap each and share lines on the AF sensor array. Each camera has a specific coverage map.

Maps of two focus systems with which I am personally very familiar. Other AF systems in modern DSLRs are similar. The area of sensitivity for most focus points in most configurations are much larger than the indicators seen through the viewfinder.

The EOS 5D mark II focus system. The dark black rectangles, along with the spot metering circle, are all that appear in the viewfinder. The larger blue rectangles are the actual coverage area for each of those points. The red rectangles are the AF Assist points active with the center point in AI Servo AF mode if Custom Function III-07 is enabled. The red assist points are not marked at all in the viewfinder!

5DII AF Map

Here is the map for the Canon 7D. The same AF system is shared by the Canon 70D. For a full explanation of the data on this chart, please see this answer

7D/70D focus system map

For a look at how this works out practically when shooting, see this entry from Andre's Blog.
For a look at how AF accuracy can vary from shot to shot, see this entry from Roger Cicala's blog at lensrentals.com. With the shallower depth of field (DoF) obtained when using wider apertures, there is less room for error and often the standard deviation of an AF system will exceed the DoF for a given focal length, aperture, and subject distance.

\$\endgroup\$
3
  • \$\begingroup\$ Thanks for the in depth explanation. But the only problem I was having is assuming the camera was awake every time I was hitting the back focus button. I have stopped using the back button for focusing because I think that isn't an intuitive operation. I rarely have this problem when I focus using the shutter button. \$\endgroup\$
    – peter
    Jul 16, 2017 at 8:44
  • \$\begingroup\$ That's one area where Nikon and Canon differ. Even when my Canon bodies are in standby mode, a press of the AF-ON button will wake them. \$\endgroup\$
    – Michael C
    Jul 16, 2017 at 21:45
  • \$\begingroup\$ @peter What setting is selected at the AE-L/AF-L Button Setting under the Buttons setting in the camera's Setup Menu? \$\endgroup\$
    – Michael C
    Jul 16, 2017 at 21:49

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.