Orquid "Phoenix"

Orquid "Phoenix"

by ceinmart

submit your photo


Hall of Fame
View past winners from this year

Please participate in Meta
and help us grow.

Take the 2-minute tour ×
Photography Stack Exchange is a question and answer site for professional, enthusiast and amateur photographers. It's 100% free, no registration required.

I took a gamble and bought a used B+W Circular Polarizer off eBay. The filter looks great but the adjusting ring is a little bit sticky. Is there some way to lubricate this?

share|improve this question
    
Are you sure it's a B+W? There are fakes that are of lesser quality. In any event, CPLs will degrade over time from wear and tear, poor handling, etc. I would be reluctant to try and lubricate as you could get the lubricant in between and it might damage the coatings. –  John Cavan Oct 20 '12 at 14:34
add comment

3 Answers

  1. Use some Isopropyl alcohol with a cotton swab around the threads. This will help clean them and evaporates without residue. (Safer than water.)

  2. Check the roundness of the filter. Perhaps it's sticking because it's out of round?

  3. You can lubricate with a bit of silicone grease or lithium grease. Both are non-reactive. Only use a very little bit! Start with a quarter of what you think you might need. It's easy to add a little bit more but frustrating to clean up after over-application.

share|improve this answer
add comment

What do you mean with sticky?

I had a Hoya HD circular polarizer that fell apart - I got it back together but it was too lose then and it was exchanged under warranty... so, a little bit on filter design.

Your filter consists of an outer as well as inner piece- these have both got a "grove", the inner piece on the outside, the other piece on the inside. The connection between the inner an outer piece is made by a brass ring with a bit cut out - so you place the ring in the inner component, squeeze together gently and lower into the other ring, it will spring back and lock the pieces in place.

To keep the filter moving smoothly, the inner ring is lubricated - if you lose the grease, the filter will become loose and may for example incur sideways movement (this is what I ended up with on the Hoya when I got it back together.) However because of the application of grease, there will be some stickyness in the system as well - on the other hand it keeps the filter in place and prevent accidental movement.

So, if your filter moves smoothly and is only a bit stiff to move, I would assume it is in perfect working condition. If it does not move smoothly it could be dirt, dents etc.

Having said that: High end filters are actually a bit stiffer than cheaper filters when it comes to turning them.

share|improve this answer
    
Did you forget the part about cleaning? Otherwise, you're not answering the question. –  Itai Oct 19 '12 at 15:15
    
2nd Itai - I assume you (DetlevCM) down-voted my answer, then didnt actually answer it yourself. –  Darkcat Studios Oct 19 '12 at 19:54
    
@Itai Read again? I am saying that if it is just a bit stiff then it is normal. Given that "sticky" isn't defined more closely it can just be that the OP didn't expect the filter to be stiffer. And apart from cleaning the glass, there is no way you can clean that actual "turning mechanism" itself. If you wash out any grease you end up with a wobbly filter. –  DetlevCM Oct 20 '12 at 10:06
    
No I did not downvote... I thought you just skipped and could have added something about it. I normally downvote when I think an answer is providing wrong information. Nothing you said qualifies :) –  Itai Oct 20 '12 at 13:58
add comment

I would give it a bath in distilled water (leave it in for a while), including turning it under water, this will remove any crud.

Normal tap water would be OK too.

see how it is after drying, if its still a bit sticky, a very small drop of machine oil would help.

share|improve this answer
    
I would disagree with the use of normal tap water. The coatings on the circular polariser may be affected by tap water especially if it is "hard" water (ie, with higher chalk content). I'd even be somewhat against distilled water as a circ/pl rotates and therefore has a mechanism that I wouldn't necessarily want water - even distilled - getting into. –  Mike Oct 19 '12 at 9:26
    
the "mechanism" is purely metal-on-metal, even if there is plastic/rubber in there, its never going to be damaged by water, assuming its not mild steel (rust) which a retaining ring may be. Tap water would be OK briefly, but not for a soak. As long as its dried out thoroughly after the soaking (would recommend an air duster to blow liquid out, and a warm rest for a few days. –  Darkcat Studios Oct 19 '12 at 9:37
2  
I would not immerse any components in water if there can be water retained in them for a start. Add to that, the mechanism on the filter is greased - while water shouldn't wash it out, you don't want a grease/water emulsion. –  DetlevCM Oct 19 '12 at 12:29
    
That's why you let it dry out........................ AS I STATED......... Whoever down-voted my answer: lets see your answers then?????? HOW ARE YOU GOING TO GET RID OF INGRAINED DIRT WITHOUT IMMERSING THE MECHANISM IN CLEANING FLUID???????????? –  Darkcat Studios Oct 19 '12 at 19:53
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.