Not Your Everyday Banana

by Bart Arondson

submit your photo


Hall of Fame
View past winners from this year

Please participate in Meta
and help us grow.

Take the 2-minute tour ×
Photography Stack Exchange is a question and answer site for professional, enthusiast and amateur photographers. It's 100% free, no registration required.

So, this blog (credit to mattdm for pointing it out) says:

Firstly, when you turn the lens around you obviously lose the CPU connection between the lens and the camera, so say goodbye to autofocus, metering (in most cases) and aperture control (though I’ll come back to that)

Then:

The advantage of this old lens is that it has a manual aperture ring, which neatly neutralises the loss of automatic control mentioned above.

So, since G lenses don't have an aperture ring, aperture can't be controlled anyhow if we reverse the lens?

Secondly, is it practical that we set the metering and the aperture (manually) before taking the lens out and reversing it?

Is there any other way to get around this problem in G lenses (assuming that the camera bodies have the manual focus, aperture, metering controls)?

share|improve this question
2  
If you read further through the blog, you will see a tip: simply actuate the aperture lever on your lens and hold it in place with a piece of poster tack. Generally this is easiest when you are holding the aperture wide open, but you can theoretically set it anywhere (though you won't know exactly what aperture you're using). It does work - I wrote the blog! :) –  ElendilTheTall Feb 18 '12 at 15:39
    
@ElendilTheTall Wow, so you wrote that blog?? Great! Anyway, I saw some statement like that there but I couldn't understand exactly what it meant or is t even "practical"! –  TheIndependentAquarius Feb 18 '12 at 15:50
    
It's very possible and gives good results. The wasp photo at the top of the blog post was taken with a Nikon kit 18-55mm lens with a blob of tack on the aperture lever, just as the blog describes. –  ElendilTheTall Feb 18 '12 at 15:53
add comment

1 Answer 1

up vote 2 down vote accepted

With some non-G lenses, there is a switch on the lens that will release the aperture ring so that you can manually control it, even off camera or reversed, to set the aperture to whatever value you want (but as you close down the aperture, the viewfinder will get dimmer).

With G lenses, there is no aperture ring. There is a mechanical lever though, which closes down the aperture. You can slide that lever and the aperture will close. As the blog points out, you can fix that lever in place with tape or poster tack.

When you reverse the lens, the aperture will close to its smallest opening (f/22 or whatever). Moving that lever can open it back up to the widest aperture, or somewhere inbetween (although very hard to control exactly)

The camera body will not know what aperture is set since it will not have any electrical contact (and will wonder where that lever went!). So best to set exposure to manual and set an appropriate shutter speed. You won't need to set an aperture since the camera can't control it anyway.

There isn't really any point in setting the metering before reversing for a number of reasons:

  • metering will assume an aperture, but once reversed you will be setting (potentially) a different aperture using that lever

  • you are unlikely to get the same amount of light through the lens when reversed, depending on the size of the two ends of the lens - most surely there will be less light transmitted when reversed.

share|improve this answer
2  
It's not just best to set the camera to Manual, it's usually essential - most cameras refuse to take a photo without a lens attached in any other mode than manual. –  ElendilTheTall Feb 18 '12 at 15:40
add comment

Your Answer

 
discard

By posting your answer, you agree to the privacy policy and terms of service.

Not the answer you're looking for? Browse other questions tagged or ask your own question.